BB Nano - Electronic Blower, Vacuum-Ready (40km/h)
Ninety-nine grams of dust removal that lives in your camera bag. Vacuuming shown with the optional NIA007 kit.
The dust blower small enough to actually carry
Most cleaning gear stays on the desk at home, which is exactly where it is useless. The BB Nano weighs 99g and fits in a jacket pocket, so it is with you when the dust shows up.
- 40km/h of constant airflow at 2.6 kPa, 73.3% higher pressure than a conventional air blower
- High-density filter keeps the dust it picks up from landing back on your gear
- Around 90 cleans per charge on high, and 210 on low
- USB-C rechargeable, roughly an hour from flat to full
- 99g and 47mm x 47mm x 92mm, smaller than a standard soft drink can
Put the last can of compressed air behind you
ONE PURCHASE, NOT A REFILL HABIT - Canned air runs out, and the next can costs the same as the last one. The BB Nano charges over USB-C and delivers around 90 cleans on high or 210 on low from a single charge, so the running cost is the electricity and nothing else.
CONSTANT AIRFLOW, NOT A SQUEEZE - A rubber bulb gives you one short puff for every squeeze. The BB Nano holds a steady 40km/h stream for as long as you press the button, which is what clears a keyboard well or a lens barrel properly rather than just moving the dust around.
NOTHING TO REFILL, NOTHING TO STORE - There is no propellant and no pressurised can. It travels with your kit and sits in a drawer between jobs without going stale or running down.
The filter is the part that protects your sensor
This is the difference between an electronic blower and the cheap bulb in the bottom of your bag.
A blower is only as clean as the air it draws in. The BB Nano pulls air through a unidirectional high-density filter, a 250-mesh weave that is about 25% denser than the 200-mesh filters used in conventional blowers. Fine dust gets intercepted on the way in instead of being fired back out at the surface you are trying to clean.
That matters most on the gear where a stray particle does real damage: an exposed camera sensor during a lens change, a watch face, a mechanical keyboard, the fan intake on a laptop. The filter is a replaceable part, so the protection stays as good as new for the life of the blower.
Smaller than the can it replaces
POCKET AND CAMERA BAG SIZED - At 47mm x 47mm x 92mm and 99g, the BB Nano takes up less room than a compact camera body. It slips into the spare pocket of a camera bag, a laptop sleeve or a jacket, which is what turns cleaning from a chore you schedule into something you do on the spot.
ONE-HAND OPERATION - Hold the body, press the switch, work the nozzle where you need it. The other hand stays free for the lens cap, the keycap or the camera you are holding steady.
TWO SPEEDS, TWO MODES - High for a fast pass over a keyboard or a jacket, low for delicate work close to glass and coatings. Press for a short burst, or hold for constant airflow.
BUILT TO BE THROWN IN A BAG - A high-quality PC shell and a skin-friendly silicone nozzle mean it takes the knocks of everyday carry, and the soft nozzle will not scratch what it touches.
Small body, serious pressure
A 30W high-power motor driving an integrated 18-blade impeller.
The BB Nano moves air at 2.6 kPa, which is 73.3% more dust removal pressure than a conventional air blower produces. Wind speed reaches 40km/h on high and settles to 15km/h on low.
Pressure is what lifts dust that has settled into a corner rather than skating over it. It is the reason a short pass clears a keyboard well, and the reason grit comes out of a hinge or a vent instead of being pushed further in.
Vacuum ready, with the optional NIA007 kit
The BB Nano body can pull as well as push. The attachments that let it do so are sold separately as the NIA007 Extension Vacuum Kit, and they are not included with this blower.
Blowing is the right tool most of the time. It clears a keyboard, a lens barrel or a vent in seconds and nothing needs emptying afterwards. The times you want the dust captured instead of relocated, the NIA007 clips on and reverses the airflow.
The kit adds a clear dust bin that twists off for emptying, a 250-mesh filter that keeps what you collect out of the air duct, an extended silicone nozzle for narrow gaps, and a brush nozzle for fabric and trim. Owners tend to reach for it on car interiors, desk drawers and camera-bag bases.
Add the NIA007 Extension Vacuum Kit
OUTPUT AND RUNTIME
| MODE | PRESSURE | WIND SPEED | CLEANING RATE |
| High Air Pressure |
±2.6 kPa |
40km/h |
Approx 90 times |
| Low Air Pressure |
±1.3 kPa |
15km/h |
Approx 210 times |
TECHNICAL SPECS
| Input |
5V⎓2A (USB-C) |
| Rated Power |
30W |
| Battery Capacity | 1,300mAh / 4.8Wh Li-ion |
| Charging Time |
Approx 1 hour |
| Filter |
Unidirectional High Density (250 mesh) |
| Material |
PC shell, silicone nozzle |
| Dimensions |
47mm x 47mm x 92mm (1.85" x 1.85" x 3.62") |
| Weight |
99g / 3.49 oz |
| Download Instruction Manual (PDF) | |
FREQUENTLY ASKED QUESTIONS
Yes, and the filter is the reason. Air is drawn in through a 250-mesh high-density filter, so the blower is not picking up ambient dust and firing it back at the sensor. Use the low setting and keep the nozzle a short distance from the surface, the same way you would with any blower.
Around 90 on the high setting and 210 on low, from the built-in 1,300mAh battery. A flat battery takes about an hour to charge over USB-C, and the power indicator shows what is left before you head out.
The BB Nano vacuums once the NIA007 Extension Vacuum Kit is fitted, and that kit is a separate purchase. What you receive here is the blower and its silicone nozzle. The kit adds the dust bin, the 250-mesh filter and the two vacuum nozzles.
It can. The filter is a serviceable part, and replacements are stocked as the NIA006 Replacement Air Filter. Swapping it restores the original airflow and keeps the intake doing its job.
What's In The Box
- 1x BB NANO Electronic Dust Blower
- 1x Silicone Nozzle
The built-in battery charges over USB-C, so there is nothing else to buy before the first clean. Vacuuming needs the NIA007 Extension Vacuum Kit, which is sold separately.
Ready to Order?
Add to cartMore Images
BB Nano - Electronic Blower, Vacuum-Ready (40km/h)
Ninety-nine grams of dust removal that lives in your camera bag. Vacuuming shown with the optional NIA007 kit.
The dust blower small enough to actually carry
Most cleaning gear stays on the desk at home, which is exactly where it is useless. The BB Nano weighs 99g and fits in a jacket pocket, so it is with you when the dust shows up.
- 40km/h of constant airflow at 2.6 kPa, 73.3% higher pressure than a conventional air blower
- High-density filter keeps the dust it picks up from landing back on your gear
- Around 90 cleans per charge on high, and 210 on low
- USB-C rechargeable, roughly an hour from flat to full
- 99g and 47mm x 47mm x 92mm, smaller than a standard soft drink can
Put the last can of compressed air behind you
ONE PURCHASE, NOT A REFILL HABIT - Canned air runs out, and the next can costs the same as the last one. The BB Nano charges over USB-C and delivers around 90 cleans on high or 210 on low from a single charge, so the running cost is the electricity and nothing else.
CONSTANT AIRFLOW, NOT A SQUEEZE - A rubber bulb gives you one short puff for every squeeze. The BB Nano holds a steady 40km/h stream for as long as you press the button, which is what clears a keyboard well or a lens barrel properly rather than just moving the dust around.
NOTHING TO REFILL, NOTHING TO STORE - There is no propellant and no pressurised can. It travels with your kit and sits in a drawer between jobs without going stale or running down.
The filter is the part that protects your sensor
This is the difference between an electronic blower and the cheap bulb in the bottom of your bag.
A blower is only as clean as the air it draws in. The BB Nano pulls air through a unidirectional high-density filter, a 250-mesh weave that is about 25% denser than the 200-mesh filters used in conventional blowers. Fine dust gets intercepted on the way in instead of being fired back out at the surface you are trying to clean.
That matters most on the gear where a stray particle does real damage: an exposed camera sensor during a lens change, a watch face, a mechanical keyboard, the fan intake on a laptop. The filter is a replaceable part, so the protection stays as good as new for the life of the blower.
Smaller than the can it replaces
POCKET AND CAMERA BAG SIZED - At 47mm x 47mm x 92mm and 99g, the BB Nano takes up less room than a compact camera body. It slips into the spare pocket of a camera bag, a laptop sleeve or a jacket, which is what turns cleaning from a chore you schedule into something you do on the spot.
ONE-HAND OPERATION - Hold the body, press the switch, work the nozzle where you need it. The other hand stays free for the lens cap, the keycap or the camera you are holding steady.
TWO SPEEDS, TWO MODES - High for a fast pass over a keyboard or a jacket, low for delicate work close to glass and coatings. Press for a short burst, or hold for constant airflow.
BUILT TO BE THROWN IN A BAG - A high-quality PC shell and a skin-friendly silicone nozzle mean it takes the knocks of everyday carry, and the soft nozzle will not scratch what it touches.
Small body, serious pressure
A 30W high-power motor driving an integrated 18-blade impeller.
The BB Nano moves air at 2.6 kPa, which is 73.3% more dust removal pressure than a conventional air blower produces. Wind speed reaches 40km/h on high and settles to 15km/h on low.
Pressure is what lifts dust that has settled into a corner rather than skating over it. It is the reason a short pass clears a keyboard well, and the reason grit comes out of a hinge or a vent instead of being pushed further in.
Vacuum ready, with the optional NIA007 kit
The BB Nano body can pull as well as push. The attachments that let it do so are sold separately as the NIA007 Extension Vacuum Kit, and they are not included with this blower.
Blowing is the right tool most of the time. It clears a keyboard, a lens barrel or a vent in seconds and nothing needs emptying afterwards. The times you want the dust captured instead of relocated, the NIA007 clips on and reverses the airflow.
The kit adds a clear dust bin that twists off for emptying, a 250-mesh filter that keeps what you collect out of the air duct, an extended silicone nozzle for narrow gaps, and a brush nozzle for fabric and trim. Owners tend to reach for it on car interiors, desk drawers and camera-bag bases.
Add the NIA007 Extension Vacuum Kit
OUTPUT AND RUNTIME
| MODE | PRESSURE | WIND SPEED | CLEANING RATE |
| High Air Pressure |
±2.6 kPa |
40km/h |
Approx 90 times |
| Low Air Pressure |
±1.3 kPa |
15km/h |
Approx 210 times |
TECHNICAL SPECS
| Input |
5V⎓2A (USB-C) |
| Rated Power |
30W |
| Battery Capacity | 1,300mAh / 4.8Wh Li-ion |
| Charging Time |
Approx 1 hour |
| Filter |
Unidirectional High Density (250 mesh) |
| Material |
PC shell, silicone nozzle |
| Dimensions |
47mm x 47mm x 92mm (1.85" x 1.85" x 3.62") |
| Weight |
99g / 3.49 oz |
| Download Instruction Manual (PDF) | |
FREQUENTLY ASKED QUESTIONS
Yes, and the filter is the reason. Air is drawn in through a 250-mesh high-density filter, so the blower is not picking up ambient dust and firing it back at the sensor. Use the low setting and keep the nozzle a short distance from the surface, the same way you would with any blower.
Around 90 on the high setting and 210 on low, from the built-in 1,300mAh battery. A flat battery takes about an hour to charge over USB-C, and the power indicator shows what is left before you head out.
The BB Nano vacuums once the NIA007 Extension Vacuum Kit is fitted, and that kit is a separate purchase. What you receive here is the blower and its silicone nozzle. The kit adds the dust bin, the 250-mesh filter and the two vacuum nozzles.
It can. The filter is a serviceable part, and replacements are stocked as the NIA006 Replacement Air Filter. Swapping it restores the original airflow and keeps the intake doing its job.
What's In The Box
- 1x BB NANO Electronic Dust Blower
- 1x Silicone Nozzle
The built-in battery charges over USB-C, so there is nothing else to buy before the first clean. Vacuuming needs the NIA007 Extension Vacuum Kit, which is sold separately.
Ready to Order?
Add to cartProduct Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Ninety-nine grams of dust removal that lives in your camera bag. Vacuuming shown with the optional NIA007 kit.
The dust blower small enough to actually carry
Most cleaning gear stays on the desk at home, which is exactly where it is useless. The BB Nano weighs 99g and fits in a jacket pocket, so it is with you when the dust shows up.
- 40km/h of constant airflow at 2.6 kPa, 73.3% higher pressure than a conventional air blower
- High-density filter keeps the dust it picks up from landing back on your gear
- Around 90 cleans per charge on high, and 210 on low
- USB-C rechargeable, roughly an hour from flat to full
- 99g and 47mm x 47mm x 92mm, smaller than a standard soft drink can
Put the last can of compressed air behind you
ONE PURCHASE, NOT A REFILL HABIT - Canned air runs out, and the next can costs the same as the last one. The BB Nano charges over USB-C and delivers around 90 cleans on high or 210 on low from a single charge, so the running cost is the electricity and nothing else.
CONSTANT AIRFLOW, NOT A SQUEEZE - A rubber bulb gives you one short puff for every squeeze. The BB Nano holds a steady 40km/h stream for as long as you press the button, which is what clears a keyboard well or a lens barrel properly rather than just moving the dust around.
NOTHING TO REFILL, NOTHING TO STORE - There is no propellant and no pressurised can. It travels with your kit and sits in a drawer between jobs without going stale or running down.
The filter is the part that protects your sensor
This is the difference between an electronic blower and the cheap bulb in the bottom of your bag.
A blower is only as clean as the air it draws in. The BB Nano pulls air through a unidirectional high-density filter, a 250-mesh weave that is about 25% denser than the 200-mesh filters used in conventional blowers. Fine dust gets intercepted on the way in instead of being fired back out at the surface you are trying to clean.
That matters most on the gear where a stray particle does real damage: an exposed camera sensor during a lens change, a watch face, a mechanical keyboard, the fan intake on a laptop. The filter is a replaceable part, so the protection stays as good as new for the life of the blower.
Smaller than the can it replaces
POCKET AND CAMERA BAG SIZED - At 47mm x 47mm x 92mm and 99g, the BB Nano takes up less room than a compact camera body. It slips into the spare pocket of a camera bag, a laptop sleeve or a jacket, which is what turns cleaning from a chore you schedule into something you do on the spot.
ONE-HAND OPERATION - Hold the body, press the switch, work the nozzle where you need it. The other hand stays free for the lens cap, the keycap or the camera you are holding steady.
TWO SPEEDS, TWO MODES - High for a fast pass over a keyboard or a jacket, low for delicate work close to glass and coatings. Press for a short burst, or hold for constant airflow.
BUILT TO BE THROWN IN A BAG - A high-quality PC shell and a skin-friendly silicone nozzle mean it takes the knocks of everyday carry, and the soft nozzle will not scratch what it touches.
Small body, serious pressure
A 30W high-power motor driving an integrated 18-blade impeller.
The BB Nano moves air at 2.6 kPa, which is 73.3% more dust removal pressure than a conventional air blower produces. Wind speed reaches 40km/h on high and settles to 15km/h on low.
Pressure is what lifts dust that has settled into a corner rather than skating over it. It is the reason a short pass clears a keyboard well, and the reason grit comes out of a hinge or a vent instead of being pushed further in.
Vacuum ready, with the optional NIA007 kit
The BB Nano body can pull as well as push. The attachments that let it do so are sold separately as the NIA007 Extension Vacuum Kit, and they are not included with this blower.
Blowing is the right tool most of the time. It clears a keyboard, a lens barrel or a vent in seconds and nothing needs emptying afterwards. The times you want the dust captured instead of relocated, the NIA007 clips on and reverses the airflow.
The kit adds a clear dust bin that twists off for emptying, a 250-mesh filter that keeps what you collect out of the air duct, an extended silicone nozzle for narrow gaps, and a brush nozzle for fabric and trim. Owners tend to reach for it on car interiors, desk drawers and camera-bag bases.
Add the NIA007 Extension Vacuum Kit
OUTPUT AND RUNTIME
| MODE | PRESSURE | WIND SPEED | CLEANING RATE |
| High Air Pressure |
±2.6 kPa |
40km/h |
Approx 90 times |
| Low Air Pressure |
±1.3 kPa |
15km/h |
Approx 210 times |
TECHNICAL SPECS
| Input |
5V⎓2A (USB-C) |
| Rated Power |
30W |
| Battery Capacity | 1,300mAh / 4.8Wh Li-ion |
| Charging Time |
Approx 1 hour |
| Filter |
Unidirectional High Density (250 mesh) |
| Material |
PC shell, silicone nozzle |
| Dimensions |
47mm x 47mm x 92mm (1.85" x 1.85" x 3.62") |
| Weight |
99g / 3.49 oz |
| Download Instruction Manual (PDF) | |
FREQUENTLY ASKED QUESTIONS
Yes, and the filter is the reason. Air is drawn in through a 250-mesh high-density filter, so the blower is not picking up ambient dust and firing it back at the sensor. Use the low setting and keep the nozzle a short distance from the surface, the same way you would with any blower.
Around 90 on the high setting and 210 on low, from the built-in 1,300mAh battery. A flat battery takes about an hour to charge over USB-C, and the power indicator shows what is left before you head out.
The BB Nano vacuums once the NIA007 Extension Vacuum Kit is fitted, and that kit is a separate purchase. What you receive here is the blower and its silicone nozzle. The kit adds the dust bin, the 250-mesh filter and the two vacuum nozzles.
It can. The filter is a serviceable part, and replacements are stocked as the NIA006 Replacement Air Filter. Swapping it restores the original airflow and keeps the intake doing its job.
What's In The Box
- 1x BB NANO Electronic Dust Blower
- 1x Silicone Nozzle
The built-in battery charges over USB-C, so there is nothing else to buy before the first clean. Vacuuming needs the NIA007 Extension Vacuum Kit, which is sold separately.
