BB2 - Electronic Dust Blower (80km/h)
Powered air for cleaning lenses, sensors and delicate gear.
Electronic dust removal at 80 km/h, with a built-in brush and a high-CRI light, in a tool that lives in the camera bag.
š Winner of the iF Design Award 2022 and the Red Dot Award 2022
- 80 km/h (49.7 mph) maximum wind for clearing dust off lenses and gear
- 2.7 kPa dust-removal wind pressure, 80% stronger than a squeeze-bulb blower
- 33.6W motor at 30,000 RPM, driving a 42mm 20-blade impeller
- Three modes on a dial: Turbo, Optical for sensors, and a quiet 55dB Silent
- Magnetic quick-release brush plus a high-CRI LED for shadowed crevices
- High-density filtered intake, so it blows clean air rather than grit
- Built-in 7.2Wh battery and USB-C charging, 210g and pocket-sized
Steady, powered air whenever you need it.
The BB2 replaces the squeeze-bulb blower with a 33.6W electronic motor, so a press of the button gives you a constant 80 km/h stream rather than a few weak puffs. That clears dust from a lens, a camera body or a keyboard in one pass.
A dial at the base sets the strength, so you choose a full Turbo blast for gear or a gentler flow for fine work, then keep it going as long as the job takes.
80 km/h that does real cleaning work.
At full power the BB2 pushes air at 80 km/h with 2.7 kPa of wind pressure, around 80% more pressure than a conventional rubber blower. That extra force lifts dust off a wider area and shifts the stubborn particles a hand-pump leaves behind.
More air per pass means fewer passes, so a sensor swab session or a lens clean takes a fraction of the fiddling.
Clean, filtered air on every pass.
A high-density filter sits over a unidirectional intake, so the air the BB2 draws in is filtered before it reaches your gear. You get a clean, dry stream aimed at the dust rather than a cloud of recirculated grit blown back onto the lens.
The intake is sealed and one-way by design, which keeps loose particles out of the airflow and away from delicate surfaces.
WHY THE BB2 OVER A MANUAL OR CANNED BLOWER
2.7 kPa on tap, held for as long as you hold the button, where a rubber bulb fades with every tiring squeeze.
A filtered intake gives a clean dry stream with no propellant and no cold liquid spray, so it is safe for sensors and lenses.
A rechargeable USB-C tool you keep in the bag, instead of cans that run out and a bulb that perishes.
A magnetic brush and a high-CRI LED ride on the nozzle, so you loosen, light and blow dust with one tool.
A 33.6W motor built for the job.
The BB2 runs a 33.6W motor spinning to 30,000 RPM, roughly 51% more motor power than the previous generation. That is the headroom that turns a gentle breeze into an 80 km/h working gust.
It comes up to speed quickly and holds it steady, so the air pressure stays the same from the first second to the last.
An air duct and impeller tuned for efficient airflow.
A 42mm impeller with 20 high-density spiral blades sits inside an air duct shaped using fluid dynamics. The duct reduces wind resistance while lifting wind power, so more of the motor's output reaches the nozzle.
The compact, efficient design is also part of how the BB2 keeps the Silent mode down to a workable 55dB.
A high-CRI light for the spots you cannot see.
A high-CRI light (CRI greater than or equal to 90) sits at the front nozzle and switches on for cleaning in shadow. Accurate colour makes a speck of dust on a dark sensor or in a deep crevice easy to spot.
That means you clean what is actually there, on the underside of a control dial or inside a battery door, rather than guessing in poor light.
A magnetic brush that loosens before it blows.
A magnetic quick-release brush clips onto the nozzle, so you can loosen stubborn particles with the brush and clear them with the air in the same motion. The brush snaps off and on as fast as the job changes.
The magnetic brush in the box handles camera bodies and grips, and the magnetic mount lets you swap attachments for different surfaces by hand.
Reach further with the optional cleaning kit.
The BB2 arrives with its magnetic brush ready to go. When the job calls for narrow gaps and larger surfaces, the BB2 Multipurpose Cleaning Kit adds three attachments that click straight onto the same nozzle. It is sold separately.
- Extended dusting brush for clearing large areas quickly
- Extended nozzle with brush for deep cleaning in narrow places
- Crevice nozzle for brush-and-blow cleaning of tight gaps
Add the BB2 Multipurpose Cleaning Kit
Three modes, set on a dial.
Turbo gives the full 80 km/h for camera bodies, flashes and grips. Optical eases the flow to a 55 km/h stream tuned for camera sensors, controlled enough for delicate work. Silent drops to a quiet 30 km/h at around 55dB for close work and indoor use.
A Lock setting on the same dial keeps the BB2 from switching on by accident in a bag or pocket.
USB-C charging and a battery that lasts a shoot.
A built-in 650mAh 11.1V (7.2Wh) battery gives around 210 ten-second bursts in Optical mode, which covers a lot of sensor and lens passes across a session. On the quiet Silent setting it stretches to over two hours of running.
Recharge over USB-C from a wall charger or a power bank, and a coloured power indicator shows green above 50%, blue under 50% and red under 10% so you know where you stand.
WHAT PEOPLE CLEAN WITH THE BB2
Clear dust off front elements, mounts and grips on Turbo before a shoot or after a dusty location.
Use Optical mode for a controlled stream tuned to lift dust from an exposed sensor.
Blow crumbs and dust from between keys, fans and ports, with the brush to loosen what sticks.
Quiet Silent mode and the high-CRI light suit fine detail on watches, drones and models.
CLEANING TIMES & WIND SPEED
| MODE | WIND SPEED | 10s BURSTS | CONTINUOUS |
| Turbo | 80 km/h (49.7 mph) | 90 times | 15 min |
| Optical | 55 km/h (34.2 mph) | 120 times | 20 min |
| Silent | 30 km/h (18.6 mph) | 800 times | 2h 13min |
*Reference figures
Measured from a full charge in laboratory conditions; real figures vary with use.TECHNICAL SPECIFICATIONS
| Max Wind Speed | 80 km/h (49.7 mph) |
| Wind Pressure | 2.7 kPa |
| Rated Power | 33.6W |
| Rotational Speed | 30,000 RPM |
| Impeller | 42mm, 20 spiral blades |
| Modes | Turbo / Optical / Silent / Lock |
| Silent Mode Noise | 55 dB |
| LED Light | High CRI (CRI ā„ 90) |
| Filter | High-density unidirectional intake |
| Battery | Built-in 650mAh / 11.1V (7.2Wh) Li-ion |
| Input | USB-C, 5Vā2A |
| Nozzle | Premium silicone |
| Body Material | Aerospace-grade aluminium alloy |
| Dimensions | 141 Ć 62 Ć 32 mm |
| Weight | 210 g (7.4 oz) |
| Download Instruction Manual (PDF) | |
FREQUENTLY ASKED QUESTIONS
Yes. Optical mode is tuned for sensor cleaning, giving a controlled 55 km/h stream of clean, dry, filtered air with no propellant and no liquid spray. The unidirectional filter keeps loose particles out of the airflow, and as with any blower you hold a sensible distance and work in short passes.
A full charge gives around 210 ten-second bursts in Optical mode, or up to 15 minutes continuous on Turbo and over two hours on Silent. Recharge over USB-C from a wall charger or a power bank, and the coloured power indicator shows green above 50%, blue under 50% and red under 10%.
Yes. The magnetic brush in the box mounts and releases with a quick pull, so you can swap it for a different attachment to match the surface. For narrow gaps and larger areas, the optional BB2 Multipurpose Cleaning Kit adds an extended dusting brush, an extended nozzle with brush and a crevice nozzle. It is sold separately.
What's In The Box
- 1x BB2 Electronic Dust Blower - with built-in 7.2Wh battery
- 1x Magnetic Quick Release Brush - camera body cleaning brush
- 1x Transparent Dust Cap
- 1x USB-C Charging Cable
For narrow gaps and larger surfaces, the BB2 Multipurpose Cleaning Kit adds three more attachments and is sold separately.
Powered, filtered air for the gear you care about.
GET YOUR BB2 NOWOriginal: $138.78
-65%$138.78
$48.57More Images
BB2 - Electronic Dust Blower (80km/h)
Powered air for cleaning lenses, sensors and delicate gear.
Electronic dust removal at 80 km/h, with a built-in brush and a high-CRI light, in a tool that lives in the camera bag.
š Winner of the iF Design Award 2022 and the Red Dot Award 2022
- 80 km/h (49.7 mph) maximum wind for clearing dust off lenses and gear
- 2.7 kPa dust-removal wind pressure, 80% stronger than a squeeze-bulb blower
- 33.6W motor at 30,000 RPM, driving a 42mm 20-blade impeller
- Three modes on a dial: Turbo, Optical for sensors, and a quiet 55dB Silent
- Magnetic quick-release brush plus a high-CRI LED for shadowed crevices
- High-density filtered intake, so it blows clean air rather than grit
- Built-in 7.2Wh battery and USB-C charging, 210g and pocket-sized
Steady, powered air whenever you need it.
The BB2 replaces the squeeze-bulb blower with a 33.6W electronic motor, so a press of the button gives you a constant 80 km/h stream rather than a few weak puffs. That clears dust from a lens, a camera body or a keyboard in one pass.
A dial at the base sets the strength, so you choose a full Turbo blast for gear or a gentler flow for fine work, then keep it going as long as the job takes.
80 km/h that does real cleaning work.
At full power the BB2 pushes air at 80 km/h with 2.7 kPa of wind pressure, around 80% more pressure than a conventional rubber blower. That extra force lifts dust off a wider area and shifts the stubborn particles a hand-pump leaves behind.
More air per pass means fewer passes, so a sensor swab session or a lens clean takes a fraction of the fiddling.
Clean, filtered air on every pass.
A high-density filter sits over a unidirectional intake, so the air the BB2 draws in is filtered before it reaches your gear. You get a clean, dry stream aimed at the dust rather than a cloud of recirculated grit blown back onto the lens.
The intake is sealed and one-way by design, which keeps loose particles out of the airflow and away from delicate surfaces.
WHY THE BB2 OVER A MANUAL OR CANNED BLOWER
2.7 kPa on tap, held for as long as you hold the button, where a rubber bulb fades with every tiring squeeze.
A filtered intake gives a clean dry stream with no propellant and no cold liquid spray, so it is safe for sensors and lenses.
A rechargeable USB-C tool you keep in the bag, instead of cans that run out and a bulb that perishes.
A magnetic brush and a high-CRI LED ride on the nozzle, so you loosen, light and blow dust with one tool.
A 33.6W motor built for the job.
The BB2 runs a 33.6W motor spinning to 30,000 RPM, roughly 51% more motor power than the previous generation. That is the headroom that turns a gentle breeze into an 80 km/h working gust.
It comes up to speed quickly and holds it steady, so the air pressure stays the same from the first second to the last.
An air duct and impeller tuned for efficient airflow.
A 42mm impeller with 20 high-density spiral blades sits inside an air duct shaped using fluid dynamics. The duct reduces wind resistance while lifting wind power, so more of the motor's output reaches the nozzle.
The compact, efficient design is also part of how the BB2 keeps the Silent mode down to a workable 55dB.
A high-CRI light for the spots you cannot see.
A high-CRI light (CRI greater than or equal to 90) sits at the front nozzle and switches on for cleaning in shadow. Accurate colour makes a speck of dust on a dark sensor or in a deep crevice easy to spot.
That means you clean what is actually there, on the underside of a control dial or inside a battery door, rather than guessing in poor light.
A magnetic brush that loosens before it blows.
A magnetic quick-release brush clips onto the nozzle, so you can loosen stubborn particles with the brush and clear them with the air in the same motion. The brush snaps off and on as fast as the job changes.
The magnetic brush in the box handles camera bodies and grips, and the magnetic mount lets you swap attachments for different surfaces by hand.
Reach further with the optional cleaning kit.
The BB2 arrives with its magnetic brush ready to go. When the job calls for narrow gaps and larger surfaces, the BB2 Multipurpose Cleaning Kit adds three attachments that click straight onto the same nozzle. It is sold separately.
- Extended dusting brush for clearing large areas quickly
- Extended nozzle with brush for deep cleaning in narrow places
- Crevice nozzle for brush-and-blow cleaning of tight gaps
Add the BB2 Multipurpose Cleaning Kit
Three modes, set on a dial.
Turbo gives the full 80 km/h for camera bodies, flashes and grips. Optical eases the flow to a 55 km/h stream tuned for camera sensors, controlled enough for delicate work. Silent drops to a quiet 30 km/h at around 55dB for close work and indoor use.
A Lock setting on the same dial keeps the BB2 from switching on by accident in a bag or pocket.
USB-C charging and a battery that lasts a shoot.
A built-in 650mAh 11.1V (7.2Wh) battery gives around 210 ten-second bursts in Optical mode, which covers a lot of sensor and lens passes across a session. On the quiet Silent setting it stretches to over two hours of running.
Recharge over USB-C from a wall charger or a power bank, and a coloured power indicator shows green above 50%, blue under 50% and red under 10% so you know where you stand.
WHAT PEOPLE CLEAN WITH THE BB2
Clear dust off front elements, mounts and grips on Turbo before a shoot or after a dusty location.
Use Optical mode for a controlled stream tuned to lift dust from an exposed sensor.
Blow crumbs and dust from between keys, fans and ports, with the brush to loosen what sticks.
Quiet Silent mode and the high-CRI light suit fine detail on watches, drones and models.
CLEANING TIMES & WIND SPEED
| MODE | WIND SPEED | 10s BURSTS | CONTINUOUS |
| Turbo | 80 km/h (49.7 mph) | 90 times | 15 min |
| Optical | 55 km/h (34.2 mph) | 120 times | 20 min |
| Silent | 30 km/h (18.6 mph) | 800 times | 2h 13min |
*Reference figures
Measured from a full charge in laboratory conditions; real figures vary with use.TECHNICAL SPECIFICATIONS
| Max Wind Speed | 80 km/h (49.7 mph) |
| Wind Pressure | 2.7 kPa |
| Rated Power | 33.6W |
| Rotational Speed | 30,000 RPM |
| Impeller | 42mm, 20 spiral blades |
| Modes | Turbo / Optical / Silent / Lock |
| Silent Mode Noise | 55 dB |
| LED Light | High CRI (CRI ā„ 90) |
| Filter | High-density unidirectional intake |
| Battery | Built-in 650mAh / 11.1V (7.2Wh) Li-ion |
| Input | USB-C, 5Vā2A |
| Nozzle | Premium silicone |
| Body Material | Aerospace-grade aluminium alloy |
| Dimensions | 141 Ć 62 Ć 32 mm |
| Weight | 210 g (7.4 oz) |
| Download Instruction Manual (PDF) | |
FREQUENTLY ASKED QUESTIONS
Yes. Optical mode is tuned for sensor cleaning, giving a controlled 55 km/h stream of clean, dry, filtered air with no propellant and no liquid spray. The unidirectional filter keeps loose particles out of the airflow, and as with any blower you hold a sensible distance and work in short passes.
A full charge gives around 210 ten-second bursts in Optical mode, or up to 15 minutes continuous on Turbo and over two hours on Silent. Recharge over USB-C from a wall charger or a power bank, and the coloured power indicator shows green above 50%, blue under 50% and red under 10%.
Yes. The magnetic brush in the box mounts and releases with a quick pull, so you can swap it for a different attachment to match the surface. For narrow gaps and larger areas, the optional BB2 Multipurpose Cleaning Kit adds an extended dusting brush, an extended nozzle with brush and a crevice nozzle. It is sold separately.
What's In The Box
- 1x BB2 Electronic Dust Blower - with built-in 7.2Wh battery
- 1x Magnetic Quick Release Brush - camera body cleaning brush
- 1x Transparent Dust Cap
- 1x USB-C Charging Cable
For narrow gaps and larger surfaces, the BB2 Multipurpose Cleaning Kit adds three more attachments and is sold separately.
Powered, filtered air for the gear you care about.
GET YOUR BB2 NOWProduct Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Powered air for cleaning lenses, sensors and delicate gear.
Electronic dust removal at 80 km/h, with a built-in brush and a high-CRI light, in a tool that lives in the camera bag.
š Winner of the iF Design Award 2022 and the Red Dot Award 2022
- 80 km/h (49.7 mph) maximum wind for clearing dust off lenses and gear
- 2.7 kPa dust-removal wind pressure, 80% stronger than a squeeze-bulb blower
- 33.6W motor at 30,000 RPM, driving a 42mm 20-blade impeller
- Three modes on a dial: Turbo, Optical for sensors, and a quiet 55dB Silent
- Magnetic quick-release brush plus a high-CRI LED for shadowed crevices
- High-density filtered intake, so it blows clean air rather than grit
- Built-in 7.2Wh battery and USB-C charging, 210g and pocket-sized
Steady, powered air whenever you need it.
The BB2 replaces the squeeze-bulb blower with a 33.6W electronic motor, so a press of the button gives you a constant 80 km/h stream rather than a few weak puffs. That clears dust from a lens, a camera body or a keyboard in one pass.
A dial at the base sets the strength, so you choose a full Turbo blast for gear or a gentler flow for fine work, then keep it going as long as the job takes.
80 km/h that does real cleaning work.
At full power the BB2 pushes air at 80 km/h with 2.7 kPa of wind pressure, around 80% more pressure than a conventional rubber blower. That extra force lifts dust off a wider area and shifts the stubborn particles a hand-pump leaves behind.
More air per pass means fewer passes, so a sensor swab session or a lens clean takes a fraction of the fiddling.
Clean, filtered air on every pass.
A high-density filter sits over a unidirectional intake, so the air the BB2 draws in is filtered before it reaches your gear. You get a clean, dry stream aimed at the dust rather than a cloud of recirculated grit blown back onto the lens.
The intake is sealed and one-way by design, which keeps loose particles out of the airflow and away from delicate surfaces.
WHY THE BB2 OVER A MANUAL OR CANNED BLOWER
2.7 kPa on tap, held for as long as you hold the button, where a rubber bulb fades with every tiring squeeze.
A filtered intake gives a clean dry stream with no propellant and no cold liquid spray, so it is safe for sensors and lenses.
A rechargeable USB-C tool you keep in the bag, instead of cans that run out and a bulb that perishes.
A magnetic brush and a high-CRI LED ride on the nozzle, so you loosen, light and blow dust with one tool.
A 33.6W motor built for the job.
The BB2 runs a 33.6W motor spinning to 30,000 RPM, roughly 51% more motor power than the previous generation. That is the headroom that turns a gentle breeze into an 80 km/h working gust.
It comes up to speed quickly and holds it steady, so the air pressure stays the same from the first second to the last.
An air duct and impeller tuned for efficient airflow.
A 42mm impeller with 20 high-density spiral blades sits inside an air duct shaped using fluid dynamics. The duct reduces wind resistance while lifting wind power, so more of the motor's output reaches the nozzle.
The compact, efficient design is also part of how the BB2 keeps the Silent mode down to a workable 55dB.
A high-CRI light for the spots you cannot see.
A high-CRI light (CRI greater than or equal to 90) sits at the front nozzle and switches on for cleaning in shadow. Accurate colour makes a speck of dust on a dark sensor or in a deep crevice easy to spot.
That means you clean what is actually there, on the underside of a control dial or inside a battery door, rather than guessing in poor light.
A magnetic brush that loosens before it blows.
A magnetic quick-release brush clips onto the nozzle, so you can loosen stubborn particles with the brush and clear them with the air in the same motion. The brush snaps off and on as fast as the job changes.
The magnetic brush in the box handles camera bodies and grips, and the magnetic mount lets you swap attachments for different surfaces by hand.
Reach further with the optional cleaning kit.
The BB2 arrives with its magnetic brush ready to go. When the job calls for narrow gaps and larger surfaces, the BB2 Multipurpose Cleaning Kit adds three attachments that click straight onto the same nozzle. It is sold separately.
- Extended dusting brush for clearing large areas quickly
- Extended nozzle with brush for deep cleaning in narrow places
- Crevice nozzle for brush-and-blow cleaning of tight gaps
Add the BB2 Multipurpose Cleaning Kit
Three modes, set on a dial.
Turbo gives the full 80 km/h for camera bodies, flashes and grips. Optical eases the flow to a 55 km/h stream tuned for camera sensors, controlled enough for delicate work. Silent drops to a quiet 30 km/h at around 55dB for close work and indoor use.
A Lock setting on the same dial keeps the BB2 from switching on by accident in a bag or pocket.
USB-C charging and a battery that lasts a shoot.
A built-in 650mAh 11.1V (7.2Wh) battery gives around 210 ten-second bursts in Optical mode, which covers a lot of sensor and lens passes across a session. On the quiet Silent setting it stretches to over two hours of running.
Recharge over USB-C from a wall charger or a power bank, and a coloured power indicator shows green above 50%, blue under 50% and red under 10% so you know where you stand.
WHAT PEOPLE CLEAN WITH THE BB2
Clear dust off front elements, mounts and grips on Turbo before a shoot or after a dusty location.
Use Optical mode for a controlled stream tuned to lift dust from an exposed sensor.
Blow crumbs and dust from between keys, fans and ports, with the brush to loosen what sticks.
Quiet Silent mode and the high-CRI light suit fine detail on watches, drones and models.
CLEANING TIMES & WIND SPEED
| MODE | WIND SPEED | 10s BURSTS | CONTINUOUS |
| Turbo | 80 km/h (49.7 mph) | 90 times | 15 min |
| Optical | 55 km/h (34.2 mph) | 120 times | 20 min |
| Silent | 30 km/h (18.6 mph) | 800 times | 2h 13min |
*Reference figures
Measured from a full charge in laboratory conditions; real figures vary with use.TECHNICAL SPECIFICATIONS
| Max Wind Speed | 80 km/h (49.7 mph) |
| Wind Pressure | 2.7 kPa |
| Rated Power | 33.6W |
| Rotational Speed | 30,000 RPM |
| Impeller | 42mm, 20 spiral blades |
| Modes | Turbo / Optical / Silent / Lock |
| Silent Mode Noise | 55 dB |
| LED Light | High CRI (CRI ā„ 90) |
| Filter | High-density unidirectional intake |
| Battery | Built-in 650mAh / 11.1V (7.2Wh) Li-ion |
| Input | USB-C, 5Vā2A |
| Nozzle | Premium silicone |
| Body Material | Aerospace-grade aluminium alloy |
| Dimensions | 141 Ć 62 Ć 32 mm |
| Weight | 210 g (7.4 oz) |
| Download Instruction Manual (PDF) | |
FREQUENTLY ASKED QUESTIONS
Yes. Optical mode is tuned for sensor cleaning, giving a controlled 55 km/h stream of clean, dry, filtered air with no propellant and no liquid spray. The unidirectional filter keeps loose particles out of the airflow, and as with any blower you hold a sensible distance and work in short passes.
A full charge gives around 210 ten-second bursts in Optical mode, or up to 15 minutes continuous on Turbo and over two hours on Silent. Recharge over USB-C from a wall charger or a power bank, and the coloured power indicator shows green above 50%, blue under 50% and red under 10%.
Yes. The magnetic brush in the box mounts and releases with a quick pull, so you can swap it for a different attachment to match the surface. For narrow gaps and larger areas, the optional BB2 Multipurpose Cleaning Kit adds an extended dusting brush, an extended nozzle with brush and a crevice nozzle. It is sold separately.
What's In The Box
- 1x BB2 Electronic Dust Blower - with built-in 7.2Wh battery
- 1x Magnetic Quick Release Brush - camera body cleaning brush
- 1x Transparent Dust Cap
- 1x USB-C Charging Cable
For narrow gaps and larger surfaces, the BB2 Multipurpose Cleaning Kit adds three more attachments and is sold separately.
